Our email: [email protected]
Weight | 5.842 lb |
---|---|
OEM | OEM P/N |
Manufacturer | Part Number |
---|---|
MRC | 7411PJDU |
Manufacturer: | MRC Bearing Service |
---|---|
Weight: | 5. 842 lbs. |
Product Name: | 7400-PJD Heavy Series Duplex Ball Bearing |
Description: | Single Row Angular Contact Bearing, 55 mm ID x 140 mm OD x 33 mm Wide, Open, Standard Precision (ABEC 1), Brass / Bronze Cage, Normal Clearance (C0), 40° Contact Angle |
Inch/Metric | Metric Bore |
---|---|
Bore Type | Round Bore |
I. D. | 55 mm |
O. D. [Min] | |
O. D. [Max] | |
O. D. | 140 mm |
Width [Min] | |
Width [Max] | |
Width | 33 mm |
Enclosure | Open |
Rows of Balls | Single |
Material | Steel |
O. D. Type | Straight |
Bearing Type | Angular Contact |
Precision | Standard |
Radial Internal Clearance Specification | Normal Clearance |
Ambient Temperature Range [Min] | |
Ambient Temperature Range [Max] | |
Ball Material | Steel |
Cage Type | Metal |
Capacity | Standard Capacity |
Contact Angle | 40° |
Guide Type | |
Lubrication | |
Outer Ring Width | 33 mm |
Precision Level | Standard (ABEC 1) |
Preload Level | None |
Seal Material | None |
Seal Type | Unsealed |
Seal Width | |
Dynamic Load Rating | 24300 lbf |
Static Load Rating [Max] | 17500 lbf |
Ball Dia. | |
Bearing Design | |
Bore B | |
Cage Material | Brass/Bronze |
Collar No. | |
Collar O. D. | |
Collar Width | |
Corner Radius [Min] | |
Eccentric Collar Offset | |
Fillet Radius | 2 mm |
Flange O. D. [Max] | |
Flange O. D. | |
Flange Width [Max] | |
Flange Width | |
Flush Ground | |
Housing Shoulder Diameter [Min] | |
Housing Shoulder Diameter [Max] | |
Housing Shoulder Diameter | |
Industry Standard Part # | |
Inner Ring O. D. | |
Inner Ring Offset | |
Inner Ring Width | 33 mm |
Internal Design | Universal Mounting |
Limiting Speed | |
Limiting Speed - Grease | 4500 rpm |
Limiting Speed - Oil | 5800 rpm |
Limiting Speed - Sealed | |
Locking Device | No Locking Device |
Lube Hole Center | |
Lubricant | Oil Preservative |
Misalignment Range | |
No. in Set | Single Bearing |
No. of Balls | |
O. D. (B) | |
Outer Ring | |
Outer Ring Inner Diameter | |
Outer Ring Size | |
Peak Running Torque (mg-mm) | |
Peak Starting Torque (mg-mm) | |
Pre Lubricant | |
Preload Amount | |
Radial Internal Clearance | Normal |
Radial Load Rating [Max] | |
Radial Rigidity (lbf/µm) | |
Reference Speed | |
Seal O. D. | |
Seal Protection Width | |
Seating Washer | |
Series | |
Set Screw Offset | |
Set Screw Size | |
Shaft Shoulder Diameter [Min] | |
Shaft Tolerance | |
Snap Ring | No Snap Ring |
Snap Ring O. D. | |
Snap Ring Offset | |
Snap Ring Thickness | |
Special Features | |
Stamping | |
Static Thrust Load Rating [Max] | |
Temperature Range [Min] | |
Temperature Range [Max] | 450 °F |
Use With | |
MRC angular contact bearings with a PJ suffix have one heavy race shoulder on the outer ring, opposing one heavy race shoulder and on recessed race shoulder on the inner ring. Because of this construction, it is possible for this bearing to incorporate a greater number of balls than a deep groove nonfilling notch bearing. The combination of maximum ball complement, optimum race groove depth, and the 40° contact angle results in high thrust load carrying capacity. 7000-PJ bearings are particularly suitable for positions where the thrust is always present in one direction. It should not be used where the bearing is subjected to radial load only, or combined radial and thrust load where the radial load is predominant. When heavy thrust must be taken in both directions, and angular contact bearing may be mounted in a duplex arrangement with another angular contact bearing or with a 9000-UP split inner ring bearing. 7000-PJ bearings are available with either peressed brass or machined brass, ball centered cages. The low shoulder diameters on the nonthrust sides of inner and outer rings, combined with large clearances between the land diameters and the cage, allow for large quantities of oil to flow through the bearings. The increased oil flow reduces operating temperature and theoretically increases bearing life. ABEC Grade 3 bore tolerances reduce the range of interference fits between the shaft and bearing bore. These tighter tolerances result in closer control of preload and minimize the risk of thermal runaway. 7400-PJ and PJD Series bearings are similar to the 7200-PJ and 7300-PH Series but are heavier sectioned and are used for very heavy thrust loads or combined radial and thrust loads where thrust is predominant.
Looking for high-quality bearings at a great price? Look no further! We have the MRC 7411PJDU bearing in stock and ready to ship to you within 3 to 7 days. With over 500 pieces available, you can order as few as 1 piece at the unbeatable price of just $501.01 per piece. Don't miss out on this fantastic deal – get the bearings you need today and keep your machinery running smoothly. Read on to learn more and make your purchase now!
We specializes in providing MRC 7411PJDU Bearings for many years, MRC 7411PJDU has a large number of stock, a number of 7411PJDU Bearings MRC suppliers and brand agency cooperation to meet your different 32307-B quality and different brand needs. Get detailed parameters can be sent to e-mail inquiry, and if you have any questions about this 32307-B bearing.
Manufacturer MRC 7411PJDU bearing with high quality. MRC 7411PJDU Bearing - 7411PJDU ANGULAR CONTACT BALL BRGS. We has been built up long-term cooperation with MRC company, could make a bulk order of the bearings Which MRC 7411PJDU is the most authentic, must choose BEARING POWER, what a whole variety, reasonable price, guaranteed quality, prompt delivery via Global express..1986 In Global stock for delivery within 3 - 7 working days. Easy ways to get the answers you need.
Stock | 500+ pcs. |
---|---|
Part number | 7411PJDU |
Manufacturer | MRC |
Total Cost | Discount |
---|---|
$0 - $2000 | 0% |
$2000 - $5000 | 1~2% |
$5000 - $20000 | 2~5% |
$20000+ | 5%~10% |